Content Previous Next

PRTG Manual: SNMP QNAP Physical Disk Sensor

<%NUMBERING1%>.<%NUMBERING2%>.<%NUMBERING3%> PRTG Manual: SNMP QNAP Physical Disk Sensor

The SNMP QNAP Physical Disk sensor monitors a physical disk in a Quality Network Appliance Provider (QNAP) network-attached storage (NAS) via the Simple Network Management Protocol (SNMP).

SNMP QNAP Physical Disk Sensor

For a detailed list and descriptions of the channels that this sensor can show, see section Channel List.

Sensor in Other Languages

Dutch: SNMP QNAP Fysieke Schijf
French: QNAP disque physique (SNMP)
German: SNMP QNAP Physikalischer Datenträger
Japanese: SNMP QNAP 物理ディスク
Portuguese: Disco físico QNAP (SNMP)
Russian: Физический диск QNAP по SNMP
Simplified Chinese: SNMP QNAP 物理磁盘
Spanish: Disco físico QNAP (SNMP)

Remarks

This sensor supports the IPv6 protocol.

This sensor has a very low performance impact.

This sensor uses lookups to determine the status values of one or more channels. This means that possible states are defined in a lookup file. You can change the behavior of a channel by editing the lookup file that the channel uses. For details, see section Define Lookups.

Add Sensor

The Add Sensor dialog appears when you manually add a new sensor to a device. It only shows the settings that are required to create the sensor. You can change nearly all settings on the sensor's Settings tab after creation.

The settings that you select in the Add Sensor dialog are valid for all sensors that you create when you finish the dialog.

QNAP NAS Settings

Setting	Description
Disk	Select the physical disks that you want to monitor. PRTG creates one sensor for each physical disk that you select. Enable check boxes in front of the respective lines to select the items. Use the check box in the table header to select all items or to cancel the selection. In large tables, use the search function in the upper-right corner.
Unit	Select the unit of the temperature measurement: Celsius Fahrenheit

Setting

Description

Disk

Select the physical disks that you want to monitor. PRTG creates one sensor for each physical disk that you select.

Enable check boxes in front of the respective lines to select the items. Use the check box in the table header to select all items or to cancel the selection. In large tables, use the search function in the upper-right corner.

Unit

Select the unit of the temperature measurement:

Celsius
Fahrenheit

Basic Sensor Settings

Click the Settings tab of a sensor to change its settings.

Basic Sensor Settings

Setting	Description
Sensor Name	Enter a name to identify the sensor.
Parent Tags	Shows tags that the sensor inherits from its parent device, parent group, and parent probe. This setting is for your information only. You cannot change it.
Tags	Enter one or more tags. Confirm each tag with the Spacebar key, a comma, or the Enter key. You can use tags to group objects and use tag-filtered views later on. Tags are not case-sensitive. Tags are automatically inherited. It is not possible to enter tags with a leading plus (+) or minus (-) sign, nor tags with parentheses (()) or angle brackets (<>). For performance reasons, it can take some minutes until you can filter for new tags that you added. The sensor has the following default tags that are automatically predefined in the sensor's settings when you add the sensor: snmpqnap qnap physicaldisk
Priority	Select a priority for the sensor. This setting determines the position of the sensor in lists. The highest priority is at the top of a list. Choose from the lowest priority () to the highest priority ().

Usually, a sensor connects to the IP Address/DNS Name of the parent device. See the device settings for details. For some sensors, you can explicitly define the monitoring target in the sensor settings.

QNAP NAS Settings

Setting	Description
Disk	Shows the physical disk that this sensor monitors. PRTG shows this value for reference purposes only. If you need to change this value, add the sensor anew.
Description	Shows information about the physical disk that this sensor monitors. PRTG shows this value for reference purposes only. If you need to change this value, add the sensor anew.
Model	Shows the model of the physical disk that this sensor monitors. PRTG shows this value for reference purposes only. If you need to change this value, add the sensor anew.
Capacity	Shows the capacity of the physical disk that this sensor monitors. PRTG shows this value for reference purposes only. If you need to change this value, add the sensor anew.
Unit	Shows the unit of the temperature measurement. PRTG shows this value for reference purposes only. If you need to change this value, add the sensor anew.

Sensor Display

Setting	Description
Primary Channel	Select a channel from the list to define it as the primary channel. In the device tree, the last value of the primary channel is always displayed below the sensor's name. The available options depend on what channels are available for this sensor. You can set a different primary channel later by clicking below a channel gauge on the sensor's Overview tab.
Graph Type	Define how different channels are shown for this sensor: Show channels independently (default): Show a graph for each channel. Stack channels on top of each other: Stack channels on top of each other to create a multi-channel graph. This generates a graph that visualizes the different components of your total traffic. You cannot use this option in combination with manual Vertical Axis Scaling (available in the channel settings).
Stack Unit	This setting is only visible if you enable Stack channels on top of each other as Graph Type. Select a unit from the list. All channels with this unit are stacked on top of each other. By default, you cannot exclude single channels from stacking if they use the selected unit. However, there is an advanced procedure to do so.

Setting

Description

Primary Channel

Select a channel from the list to define it as the primary channel. In the device tree, the last value of the primary channel is always displayed below the sensor's name. The available options depend on what channels are available for this sensor.

You can set a different primary channel later by clicking below a channel gauge on the sensor's Overview tab.

Graph Type

Define how different channels are shown for this sensor:

Show channels independently (default): Show a graph for each channel.
Stack channels on top of each other: Stack channels on top of each other to create a multi-channel graph. This generates a graph that visualizes the different components of your total traffic.
You cannot use this option in combination with manual Vertical Axis Scaling (available in the channel settings).

Stack Unit

This setting is only visible if you enable Stack channels on top of each other as Graph Type. Select a unit from the list. All channels with this unit are stacked on top of each other. By default, you cannot exclude single channels from stacking if they use the selected unit. However, there is an advanced procedure to do so.

Inherited Settings

By default, all of these settings are inherited from objects that are higher in the hierarchy. We recommend that you change them centrally in the root group settings if necessary. To change a setting for this object only, click under the corresponding setting name to disable the inheritance and to display its options.

For more information, see section Inheritance of Settings.

Scanning Interval

For more information, see section Root Group Settings, section Scanning Interval.

Schedules, Dependencies, and Maintenance Window

You cannot interrupt the inheritance for schedules, dependencies, and maintenance windows. The corresponding settings from the parent objects are always active. However, you can define additional schedules, dependencies, and maintenance windows. They are active at the same time as the parent objects' settings.

Schedules, Dependencies, and Maintenance Window

For more information, see section Root Group Settings, section Schedules, Dependencies, and Maintenance Window.

Access Rights

For more information, see section Root Group Settings, section Access Rights.

Channel List

Which channels the sensor actually shows might depend on the target device, the available components, and the sensor setup.

Channel	Description
Downtime	In the channel table on the Overview tab, this channel never shows any values. PRTG uses this channel in graphs and reports to show the amount of time in which the sensor was in the Down status in percent.
HD Status	The disk status Up status: Ready Down status: Invalid, No Disk, RwError, Unknown
S.M.A.R.T. Status	The Self-Monitoring, Analysis and Reporting Technology (S.M.A.R.T.) status of the disk Up status: Good, Normal Down status: Bad
Temperature	The temperature This channel is the primary channel by default.

Knowledge Base

What security features does PRTG include?

https://kb.paessler.com/en/topic/61108

Why do I get DoS alarms on my QNAP?

https://kb.paessler.com/en/topic/80421

My SNMP sensors don’t work. What can I do?

https://kb.paessler.com/en/topic/46863